Briggs 3.5 hp Crankshaft

Status
Not open for further replies.

Lefturns75

New member
Messages
68
Reaction score
1
Location
Podunkville USA in the ozarks
Hey guys, I know someone here can answer this for me. I have a Briggs 3 hp engine I want to use on the grandsons mini, he is a little guy and this would be enough engine for him. My problem is the PTO shaft is only 1 1/4" long. Any of you guys know a part number for a crank with a longer PTO I can use. I have looked up diagrams on various sites and found some numbers but they don't tell me the PTO length. my briggs model # is 80202 and was used on a belt drive tiller. I think the engine was manufactured in 1987. The engine is fresh and runs great so I figure a crank swap will solve my problem and I am sure there is one out there I just don't know which one I need. Ideas or suggestions anyone?
 

OzFab

Well-known member
Messages
15,615
Reaction score
76
Location
Warwick Qld, Australia
Ok, so, is it a 3hp as stated in your post or a 3.5hp as stated in the heading?

You could go to the trouble of sourcing & fitting a new crank but, in the long run, it would probably be cheaper & easier to source another engine...

Another option widely used is to simply lengthen the existing shaft, either with a machined extension which screws into the existing thread or a hollow spacer & a long bolt...
 

Lefturns75

New member
Messages
68
Reaction score
1
Location
Podunkville USA in the ozarks
If the hollow spacer & long bolt works, that is what I will try. I have never tried that trick before. I think the ".5" hp is added by the manufacture of the product, not the engine. I have looked at parts diagrams of 3, 3.5 and 3.75 engines and the internals are the same part number, I think only the carb. was different. I have found the same engine on three different brand products with different HP ratings but the engine is identical to the others. I am no Briggs expert but I am sure one can explain this to me. Thanks for the spacer tip.
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
If you want a crank with a longer tailshaft...I probably have one....the real question is...before we waste each others time.....can you accurately measure what you have and relate that?
 

Poboy kartman

Senior Moments Member
Messages
12,461
Reaction score
73
Location
White Settlement Texas
Answered the PM...but now re-reading this thread...I'm pretty sure that crank I have will fit, sooo....PM me an address and I'll send it your way.

---------- Post added at 04:07 AM ---------- Previous post was at 04:04 AM ----------

Ok, so, is it a 3hp as stated in your post or a 3.5hp as stated in the heading?

You could go to the trouble of sourcing & fitting a new crank but, in the long run, it would probably be cheaper & easier to source another engine...

Another option widely used is to simply lengthen the existing shaft, either with a machined extension which screws into the existing thread or a hollow spacer & a long bolt...

If the crank I send him fits...all he'll need is a little RTV....and I'll be out less than $10 to help out a fellow member.
 

Lefturns75

New member
Messages
68
Reaction score
1
Location
Podunkville USA in the ozarks
Quick up-date. First, big thanks to Poboy for his help on this. He gave it a good try and thanks for that Poboy!!!!! I came up with a part number and checked things out and #492880 gives me what I need. I located one on the cheap and now I will be back in business. Ever notice how nothing ever fits and when it does something else is the wrong size? I love this hobby!!!!!
 
Status
Not open for further replies.
Top