13hp or (2) 6.5 predators build

Status
Not open for further replies.

ironman

I'm Back!
Messages
906
Reaction score
2
Location
kentucky
So trying figure which I would enjoy more to build a 13 hp mini bike or a dual 6.5 build
Figure 600-1000.00 build range this will be a winter build no rush got other builds goin on right now.
Just like some input from those who have used either on a mini?


Sent from my iPhone using Tapatalk
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
When I look at most projects like this... I go with what is easiest then cheapest... but what do you have to start with Is about the easiest question off hand....then go from there...
 

itsid

Moderator
Staff member
Messages
11,563
Reaction score
261
Location
Ruhrpott [Germany]
just because of pure curiosity..
How would you fit TWO 200cc engines on a mini bike?

I mean one, sure.. a 400cc ..okay.. but two 200cc engines...
I don't see how that could fit a std mini bike frame.

'sid
 

pRoFiT

Can't buy it?, build it!
Messages
1,151
Reaction score
64
Location
California
All wheel drive maybe? Ive Seen dual inline engine mini bikes. Not sure how the drive was connected. Looked cool.
 

Hellion

Staff Murderator
Messages
9,447
Reaction score
4,373
Gentlemen, the karting world is no stranger to dual engines...

But I too would like to see a dual-engined mini bike. You got a link for the dual inline bike, pRoFiT?
All wheel drive has been done on the Rokon...
 

mckutzy

Well-known member
Messages
8,353
Reaction score
113
Location
bc, canada
Overyonder at the opposing faction.. They have talked about dual engines before. Some use a jackshaft with a freewheeler spragg bearing on one motor, both using a cent clutch.. A dual sprocket cent clutch on the rear motor. There are a few ways of doing it... Google will help a bit...
Have to extend the frame or really tilt the motors up or cylinders vertical..
 

minibiker

New member
Messages
148
Reaction score
1
Location
USA
I have seen dual 6.5 clones in a stretched frame dual cent clutch etc. But I believe a 420 cc motor will be much cheaper and easier to build than two 212s. I spent about 600 on my built 212 predator and am not impressed with the torque. I may go the same route with a 420
 

bob58o

SuckSqueezeBangBlow
Messages
9,646
Reaction score
1,866
Location
Chicago-town USA
I have definitely NOT wondered how many inches of stretch needed for a 424cc twin cylinder. Lol
http://909minibikes.com/products/nitro-44-drag-bike-roller

---------- Post added at 12:11 AM ---------- Previous post was at 12:09 AM ----------

https://m.youtube.com/watch?v=39o_oS3842c

---------- Post added at 12:12 AM ---------- Previous post was at 12:11 AM ----------

Twin engine build more frustrating and more enjoyable. More satisfying.

---------- Post added at 12:42 AM ---------- Previous post was at 12:12 AM ----------

This
https://m.youtube.com/watch?v=BO0F98IRRLE
 

Hellion

Staff Murderator
Messages
9,447
Reaction score
4,373
... Have to extend the frame or really tilt the motors up or cylinders vertical..

That's what gets me sometimes. The Predator or just about any OHV engine these days has a huge footprint versus the older flatheads. One of the detriments no doubt.
 

Denny

Canned Monster
Messages
12,066
Reaction score
8,605
Location
Mayberry, Indiana
If you do twin engines on a mini-bike don't forget to use a good scrub brake. :thumbsup:

I would just use 2 of the same sprockets to hook the engines together and at the second engine put a centrifugal clutch.


Denny
 
Status
Not open for further replies.
Top