Search results

Great Place ! Great People ! Now look what you guys went and did ! Now I gotta say nice things about ya'll. I knew this place was worth becoming a member of. Seeing others help others is what its all about ! Great job on getting your kart up and running again. Have fun !

Maybe this will help. Not to imply that you know nothing about Go Karts, you may want to read through this and see if you can reach a remedy. I have seen many cases where going to a lower gearing can solve this issue. Not saying it will but without any measurements and a closer examination of...

I am posting this thread to clear up some things about the Mikuni 22mm Carb that alot of people are using. First is the CHOKE or STARTING system as Mikuni calls it: There is a lever that has the word CHOKE on it. If this lever is pushed down on the end with the lettering then the CHOKE is ON...

Mikuni 22mm Tuning Issues Ok. Update on what I found with my Mikuni 22mm. In the an earlier part of this thread I mentioned that I had to open the slider in order to start the engine and then turn the screw and let the slider fall in its bore to lower the idle. I did this again and shut the...

Another question is which way is rich on the screw. Is it in or out ? Mikuni 22mm

Have you ever heard of someone running a 10 pilot ? This motor is 11.1 comp and I have been reading some of the agk stuff and they run 12.5 and so do most others. I will try it and see what happens. Bad thing is I have to order the pilot since no one around here has them in stock. I live close...

I removed the carb and checked intake gasket and it is sealing. I am not so sure its a vacumn leak. I have to turn the screw to lift the carb barrel to allow more air in just so it will start. After it starts I can turn down the idle but get no change when I adjust the air fuel screw. All the...

Finally got my 6.5 Modified Clone started. I am having a fit trying to get this thing to idle properly. I adjust the the screw that lifts the barrel and when it starts it idles high enough to engage the Bully 2 Disk Clutch. The clutch is setup to grab at 3200 rpm. I turn the screw and lower the...

End Play You can use them only if they have the part that slides out the end when you open them but you will have to make sure that you rest them in the same place each time because any slight movement will throw off your reading. It might be a better idea to visit you local auto shop and ask...

How to measure end play There are a couple of methods you can use. You will need a dial indicator or a micrometer. I bolt ba flat piece of metal to the block that serves as a base for the magnetic base on my dial indicator. You then arrange the indicator so that the tip of the spring loaded pin...

Got my answer Russell at NR Racing stated the endplay should be .005-.007. Hope this helps someone else that needs the info.

Got my answer I just got my answer from Russell at NR Racing. He stated that the end play should be .005 -.007. Hope this helps someone else out there.

I posted this in the engine section but thought I would put it here to see if I got a response. This is the only thing I need to finish buttoning up the motor. I am doing a Hop Up on a 6.5 Clone and need the Crankshaft End Play Spec. The End Play is currently 0.017. I am using a Billet Side...

I am building a clone and was looking for some tech info and found this site. It looked like a great place join. I am 52. Served in the U.S. Army as a Ranger in a Long Range Surveillance Unit in the 70's. Got out in the early 80's and went into Law Enforsement but didn't like that so I started...

I am doing a Hop Up on a 6.5 Clone and need the Crankshaft End Play Spec. The End Play is currently 0.017. I am using a Billet Side Cover with an O-ring. I have shims for the crank: 0.02, 0.05 and 0.06X2. I also have Gaskets for the Side Cover that are 0.019. So I have many options to use to get...