Recent content by allanbranch

  1. A

    Torque Converter/Carter/Honda

    Thanks for the help thus far. TAV2 and 30 Series are helpful terms, what's the difference? Would this work? http://www.bmikarts.com/Torque-Converter-for-41-Chain-34-Bore-TAV2-Replacement_p_1029.html
  2. A

    Torque Converter/Carter/Honda

    A few years ago I took two carter frames and made it into one gokart. The little centrifugal force doesn't like all the weight especially now that we're using the cart in the backyard. The cart weighs about 100 pounds and carries 90-300 pounds in kid weight. The motor is a honda 5hp and seems...
  3. A

    Nuts

    @rocketkart, so you can tighten down a bolt but only if the size doesn't exceed the center ring of the bearing and the washer doesn't go beyond the blue line! Thanks! Do you know the size of the washer? For this bearing? http://www.mfgsupply.com/az8206.html I wish when I ordered bearings the...
  4. A

    Nuts

    @poboy what's a "Manco"? I'm using these bearings and these dust shields. http://www.mfgsupply.com/az8206.html http://www.mfgsupply.com/az8305.html What's the ideal setup?
  5. A

    Clutch ID

    Yeah, we're bending a pipe for the exhaust and covering it in heat tap. It's a pain but the engine cost me $100 to hopefully the exhaust won't be too big of a pain. Thanks for the heads up though.
  6. A

    Dies when no choke

    The carb, once it's running, drips gas from the overflow tube that runs from the bottom of the carb. When I cleaned the carb everything was really clean, no gunk anywhere, I could see thru all the holes too. I didn't touch the pilot screw, I'm trying that now.
  7. A

    Dies when no choke

    Okay I cleaned the carb, this video was actually really helpful getting etube out of my honda engine. http://www.youtube.com/watch?v=qxyTxI5H6W4 http://www.youtube.com/watch?v=V3S_7XpUioE I'm still having the same issue, what's next? Whats the best video for teaching out to tune the carb?
  8. A

    Dies when no choke

    Thanks for the advice, off to google carb cleaning!
  9. A

    Dies when no choke

    Honda 6hp XR2750 The engine dies when I lessen the choke. I know nothing about engines go easy on me.
  10. A

    Clutch ID

    It's a build, I really have three gokarts right now. I bought this frame from a scrap yard for $30, just needed new tubes, a few new bearings, 1 tire and an engine. This was bought way before i knew anything about gokarts. Then I bought an engine from a friend, he had this clutch on it, he...
  11. A

    Clutch ID

    Looks like I cannot get a Hilliard Fury clutch with a #41 sprocket. The drive sprocket is a #41 carter brothers (60 I think), so I don't want to go down the path or replacing it and the wheel hub and rim, also i have some #41 chain too. I was going to buy this sprocket but I think I have a...
  12. A

    Clutch ID

    Oops Honda 6hp XR2750, looks like it came off of a pressure washer.
  13. A

    Clutch ID

    40 vs 41 is really just width of the chain, 40 is wider. The gokart is a carter bros two seater, the engine is a 6.5hp honda.
  14. A

    Nuts

    Nylock nuts, I should have known that. I have a carter gokart, it's a 5/8 shaft on a 6" split rim. I use dust covers on the bearings and just a normal nut. But I'll switch to nylock.
  15. A

    Clutch ID

    I need a #41 chain sprocket for the clutch, are clutch sprockets interchangeable?
Top