Go Back   DIY Go Kart Forum > Building Plans And Advice > Go Kart Discussion

Notices

Closed Thread
 
Thread Tools Display Modes
  #1  
Old 10-19-2019, 06:14 AM
Andy_Tres Andy_Tres is offline
Junior Member
 
Join Date: Sep 2019
Posts: 8
Thanks: 5
Thanked 0 Times in 0 Posts
Default Crankshaft Adapter Wonít Come Off

Hey,

I have an engine with an adapter on the crankshaft. Iíve kept PB Blaster on it and tried a gear puller it get it off. It wonít budge. Anything else I could try? Any other options? Any help would be greatly appreciated!

Also, any good ways to hold the crankshaft to stop it from spinning?
Attached Thumbnails
FB542798-B7AA-4C03-B0EC-636043502945.jpg   77B9A720-7A86-46B0-909A-1C35BAB33BDA.jpg  

  #2  
Old 10-19-2019, 06:18 AM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is offline
2019 Build Off Winner!
 
Join Date: Jan 2019
Location: Texas
Posts: 3,567
Thanks: 797
Thanked 561 Times in 506 Posts
Default

Make sure all set screws have been removed.
Soak it with PB Blaster for about a week.
Try stuffing a length of soft rope down the spark plug hole to keep it from spinning.
Last resort could be to use a torch to heat it up to expand it, or to cut it off.
What dk you mean by the gear puller isn't working? Does it pop off? Does it just not move?
__________________
Currently Flathead-Crazed
  #3  
Old 10-19-2019, 07:37 AM
Andy_Tres Andy_Tres is offline
Junior Member
 
Join Date: Sep 2019
Posts: 8
Thanks: 5
Thanked 0 Times in 0 Posts
Default

The gear puller pops off and it doesnít really be seeming to move the adapter. But it may be because of how rusted it is
  #4  
Old 10-19-2019, 08:13 AM
Shep1970 Shep1970 is online now
Member
 
Join Date: Jan 2019
Location: Massachusetts
Posts: 66
Thanks: 19
Thanked 53 Times in 34 Posts
Default

Use like a 3 inch hose clamp where the teeth are to hold the puller teeth on? Make sure itís pushing against the crank end, I canít tell by the pics if thatís one piece or if itís just pulling against itself if that makes sense. May need to put a metal dowel of sorts if thereís a hole in the end ďifĒ that adapter is one piece. (Where the threads are and the end nose)
Personally Iíd ad some HEAT.
Good luck

Shep
  #5  
Old 10-19-2019, 09:03 AM
mckutzy mckutzy is offline
Senior Member
 
Join Date: May 2008
Location: bc, canada
Posts: 8,066
Thanks: 926
Thanked 1,924 Times in 1,595 Posts
Default

Need heat... lots of it...
A propane or better.. an acetylene torch would be great....
Keep the heat moving and watch out for the shaft seal....
Also, polish the end of the shaft.. that will make it easier to pull the item off..
__________________
10yr+ club..... My current ride- http://www.diygokarts.com/vb/showthread.php?t=5461
  #6  
Old 10-20-2019, 12:54 AM
Mrmonk7663 Mrmonk7663 is offline
Senior Member
 
Join Date: May 2019
Location: Houston, Texas
Posts: 456
Thanks: 113
Thanked 83 Times in 67 Posts
Default

Yep. Start off with a propane torch. Heat it up like described above. After heating use a mix of 50/50 ATF fluid and Acetone for your penetrating fluid. Use the fluid while the piece is still hot (not hot enough to ignite it obviously) if this doesn’t work it’s cutting time.
The Following User Says Thank You to Mrmonk7663 For This Useful Post:
landuse (10-21-2019)
  #7  
Old 10-20-2019, 01:41 PM
Randy H Randy H is offline
Senior Member
 
Join Date: Oct 2016
Posts: 895
Thanks: 851
Thanked 476 Times in 368 Posts
Default

A better puller world help. Three jaw. A bearing separator would givea better bite.

Use a cut off wheel to slice as deep as you dare.

Heat is useful but if you're puller is slipping off....
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 08:38 AM.