Go Back   DIY Go Kart Forum > Building Plans And Advice > Engines & Clutches

Notices

Closed Thread
 
Thread Tools Display Modes
  #1  
Old 07-12-2019, 11:22 AM
shewannameetkarty shewannameetkarty is offline
Member
 
Join Date: Jul 2019
Posts: 33
Thanks: 0
Thanked 3 Times in 3 Posts
Default >50 Tooth Sprockets for #35 Chains

I've only been able to find 50t, 60t, and 72t sprockets and I already have a 50t one, it's for a 1WD kart and I want something preferably 40t or less, down to 30t, although I have found some 40ts for other chain sizes, would I have to go through the effort of buying a new clutch and chain if I want to go any lower than 50t? For reference, it's a 6 hole
  #2  
Old 07-12-2019, 11:32 AM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is online now
2019 Build Off Winner!
 
Join Date: Jan 2019
Location: Texas
Posts: 3,628
Thanks: 806
Thanked 573 Times in 517 Posts
Default

Woahwhoawhoa! WHOA!
You are going to gear that thing WAY too high! Unless you have a jackshaft.
Please elaborate on what you are trying to do.
__________________
Currently Flathead-Crazed
  #3  
Old 07-12-2019, 11:35 AM
mckutzy mckutzy is online now
Senior Member
 
Join Date: May 2008
Location: bc, canada
Posts: 8,187
Thanks: 937
Thanked 1,949 Times in 1,619 Posts
Default

What is the kart, engine, Measured OD of tire size(NOT SIDEWALL SIZE) ect?...
Also where is your location?......

6 bolt what?... going to need measurements
__________________
10yr+ club..... My current ride- http://www.diygokarts.com/vb/showthread.php?t=5461
  #4  
Old 07-12-2019, 02:12 PM
bob58o's Avatar
bob58o bob58o is offline
The Independent Variable
 
Join Date: Jan 2016
Location: Chicago-town USA
Posts: 7,570
Thanks: 3,243
Thanked 2,274 Times in 1,760 Posts
Default

> = greater than
< = less than
__________________
There are two types of people. Those who can extrapolate from incomplete data
The Following 3 Users Say Thank You to bob58o For This Useful Post:
65ShelbyClone (07-13-2019), Joe-405 (07-12-2019), JTSpeedDemon (07-12-2019)
  #5  
Old 07-12-2019, 02:18 PM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is online now
2019 Build Off Winner!
 
Join Date: Jan 2019
Location: Texas
Posts: 3,628
Thanks: 806
Thanked 573 Times in 517 Posts
Default

I just noticed that after you pointed it out......
__________________
Currently Flathead-Crazed
  #6  
Old 07-12-2019, 03:51 PM
shewannameetkarty shewannameetkarty is offline
Member
 
Join Date: Jul 2019
Posts: 33
Thanks: 0
Thanked 3 Times in 3 Posts
Default

Quote:
Originally Posted by mckutzy View Post
What is the kart, engine, Measured OD of tire size(NOT SIDEWALL SIZE) ect?...
Also where is your location?......

6 bolt what?... going to need measurements
I'm pretty sure it's a Manco Sidekick, predator 212, 11 inch tire, 12t clutch governed, 50t sprocket, it goes ~28mph and I'd like more speed preferably without taking the governor out, I run it on flat/long neighborhood roads so I could go WOT the entire time but I keep it around 2000-2100 rpm if I'm guessing right, around 18 mph
  #7  
Old 07-12-2019, 04:55 PM
Dingocat's Avatar
Dingocat Dingocat is offline
Broke
 
Join Date: Apr 2018
Location: Cleveland Ohio
Posts: 460
Thanks: 34
Thanked 99 Times in 83 Posts
Default

There's a throttle limiting screw by the arm for the hand throttle. Lets it get up to like 4k. Should give you more speed.
__________________
If it's not scary you're not going fast enough
  #8  
Old 07-12-2019, 06:32 PM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is online now
2019 Build Off Winner!
 
Join Date: Jan 2019
Location: Texas
Posts: 3,628
Thanks: 806
Thanked 573 Times in 517 Posts
Default

Do NOT put a smaller sprocket on it! If you do you will burn up your clutch.
If you want to go faster, you can adjust the governor or remove it completely, but do not put on a smaller sprocket.
__________________
Currently Flathead-Crazed
  #9  
Old 07-12-2019, 08:30 PM
cleatusj cleatusj is offline
Junior Member
 
Join Date: Apr 2019
Location: Granbury, Texas
Posts: 20
Thanks: 0
Thanked 10 Times in 9 Posts
Default

But the clutch manufacturers need to buy their kids braces.
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 10:29 AM.