Go Back   DIY Go Kart Forum > Search Forums

Notices

Showing results 1 to 25 of 33
Search took 0.01 seconds.
Search: Posts Made By: shewannameetkarty
Forum: Engines & Clutches 04-04-2020, 12:41 AM
Replies: 331
Views: 8,106
Posted By shewannameetkarty
When exactly is "oil change on time" I've heard 6...

When exactly is "oil change on time" I've heard 6 months I've heard a year I've heard every month and I've heard every 10 hours of use, my last oil change was a couple months ago
Forum: Engines & Clutches 02-29-2020, 12:18 AM
Replies: 12
Views: 614
Posted By shewannameetkarty
so if you modified a stock rod to have this...

so if you modified a stock rod to have this journal hole could you in theory rev a stock rod higher?
Forum: Go Kart Discussion 02-26-2020, 07:23 PM
Replies: 69
Views: 2,163
Posted By shewannameetkarty
I've been thinking of instead of paying around...

I've been thinking of instead of paying around 200+ dollars on a live axle kit you could mirror the 1wd setup on the other side and have two engines, idk it's a cool idea probably not practical
Forum: Go Kart Discussion 02-22-2020, 11:35 PM
Replies: 1
Views: 379
Posted By shewannameetkarty
What tires should I use at Busco Beach?

I have a kart that runs 5 inch rims, I'm wondering what tires would work best for the loose dirt/sand at Busco, looks like nobody makes Vtreads in 5 inch sizes that's why I'm asking
Forum: Go Kart Discussion 02-08-2020, 10:09 PM
Replies: 2
Views: 290
Posted By shewannameetkarty
212 stage 1 too rich

I believe my 212 is too rich, I bought the stage 1 kit from GPS and it was running too lean to even run so I put in a richer e tube but turns out the issue was just the carburator, the engine runs...
Forum: Go Kart Discussion 12-15-2019, 06:38 PM
Replies: 6
Views: 423
Posted By shewannameetkarty
Trouble finding a spacer for my wheel

This kart came with manco rims and a manco spacer, but I switched over to a gopowersports drive wheel and so the spacing is wrong, how can I find a spacer that matches the wheel with the clutch? The...
Forum: Engines & Clutches 09-22-2019, 10:46 AM
Replies: 11
Views: 800
Posted By shewannameetkarty
With some more testing it acts like it's not...

With some more testing it acts like it's not getting enough fuel, I tried putting the old jet back in and nothing changed, if I give it gas it can stay running but it can't idle
Forum: Engines & Clutches 09-21-2019, 08:52 AM
Replies: 11
Views: 800
Posted By shewannameetkarty
yes the thinner side is up, the jet screw side is...

yes the thinner side is up, the jet screw side is face down, so idk I can get it to run on starter fluid and what might be its own gas for a little bit if I rev it up enough but then it stalls out
...
Forum: Engines & Clutches 09-21-2019, 06:55 AM
Replies: 11
Views: 800
Posted By shewannameetkarty
212 stage one won't start

I installed the stage one kit on my 212 and today it wouldn't start for the first time, full choke nothing, I have a feeling it's something I messed up with the jet. I put it in with the thinner part...
Forum: Engines & Clutches 09-09-2019, 12:51 PM
Replies: 5
Views: 490
Posted By shewannameetkarty
Forum: Go Kart Discussion 08-31-2019, 09:35 AM
Replies: 2
Views: 318
Posted By shewannameetkarty
Got these tires, do they need a tube?

I couldn't find the right size online (11x6.00-5) and the tire itself is super stiff anyway, much much stiffer than the knobby tires that's why I'm asking
Forum: Engines & Clutches 08-29-2019, 01:41 PM
Replies: 4
Views: 308
Posted By shewannameetkarty
H

Yeah pulling it harder did feel better thanks
Forum: Engines & Clutches 08-29-2019, 01:19 PM
Replies: 4
Views: 308
Posted By shewannameetkarty
I didn't touch anything else, iirc it has just a...

I didn't touch anything else, iirc it has just a tad more resistance but the last time I pulled it was about a month ago, I pulled it slow just to make sure it wouldn't get stuck or anything and I...
Forum: Engines & Clutches 08-29-2019, 12:39 PM
Replies: 4
Views: 308
Posted By shewannameetkarty
Just did a governor removal predator 212, question about the pull start

When I pull the rope it has resistance, let's up then has resistance again, but after that the whole rest of the way is free just a little more difficult to pull but not much, want to make sure if...
Forum: Engines & Clutches 08-29-2019, 11:41 AM
Replies: 4
Views: 279
Posted By shewannameetkarty
Forum: Go Kart Discussion 08-29-2019, 06:21 AM
Replies: 5
Views: 536
Posted By shewannameetkarty
So black and green to the black wire on the right?

So black and green to the black wire on the right?
Forum: Go Kart Discussion 08-28-2019, 07:20 PM
Replies: 5
Views: 536
Posted By shewannameetkarty
How do I wire the kill switch?

I had it wired up by a friend's dad, but taking the engine apart for governor removal I unplugged the wires by mistake and I'm not sure how they go back together, more specifically the kill switch,...
Forum: Go Kart Discussion 08-28-2019, 05:53 PM
Replies: 12
Views: 535
Posted By shewannameetkarty
itsid for some reason reply isn't working but you...

itsid for some reason reply isn't working but you said it might be for twin two strokes, I was hoping to drop my existing predator on it and when I score a deal on a 3hp or something I'd put it on my...
Forum: Engines & Clutches 08-26-2019, 06:33 PM
Replies: 8
Views: 517
Posted By shewannameetkarty
212 can't get c clip off governor

I literally can't get the c clip off the governor tried flathead screwdrivers, pliers, everything, how do I get the **** thing out?
Forum: Go Kart Discussion 08-25-2019, 09:00 PM
Replies: 12
Views: 535
Posted By shewannameetkarty
Do you guys think 50$ is a good deal for this?

Found really locally on Craigslist, looks like it's live axle, which is something I've been wanting for a while, already have a 212 I'm building, definitely needs some work, what do you guys think?
Forum: Engines & Clutches 08-25-2019, 02:55 PM
Replies: 2
Views: 292
Posted By shewannameetkarty
Predator 212 governor removal tool list?

Can someone type a list of the tools I'll need for a start to finish governor removal? I.e. wrench sizes, tools, bolts etc

I want to make sure I have everything I need before committing to the...
Forum: Go Kart Discussion 08-14-2019, 10:36 AM
Replies: 2
Views: 246
Posted By shewannameetkarty
1wd kart slick tires, can I use the race dish like rims?

I have a Manco Sidekick with 1wd and I've been thinking about putting slicks on it instead of the knobby tires because I'd prefer not to rip up grass. Would I be able to use rims like the ones in the...
Forum: Go Kart Discussion 07-25-2019, 02:09 PM
Replies: 5
Views: 384
Posted By shewannameetkarty
What kind of brakes can I use on 1WD?

And how would I install them?
Forum: Go Kart Discussion 07-22-2019, 02:42 PM
Replies: 3
Views: 261
Posted By shewannameetkarty
Are predator 212s single gear only?

Would I also need live axle to have a shifter?
How would I put a shifter on in the first place?
Forum: Go Kart Discussion 07-13-2019, 01:59 PM
Replies: 7
Views: 338
Posted By shewannameetkarty
What's with the abundance of Yerf Dog threads?

Are they just good karts am I missing out on something really good by not owning one?
Showing results 1 to 25 of 33

 

All times are GMT -6. The time now is 01:10 AM.