Search results

Hey guys I found a guy on craigs list who might trade his 03 crf450r for my 05 kx125 . It sounds like a good deal but I am a little uneasy about the trade. The reason being that he said he has a new top end on it but says its leaking from the water pump weep hole and the oil drain bolt. I know...

Hey guys I am selling all my mini bike frames ect, but I have a newish predator 212 that I am going to get running again. I want to put the motor in a beach cruiser bike to ride around the city and race my buddys 5 hp briggs motorized bike. I am debating whether to use a 212 or just buy a 66cc...

I have a 01 tacoma prerunner with 162000 miles that has been making a squealing noise in the rear when I am driving a low speeds. I have searched online and in the manual and have found nothing. I believe it may be the rear bearings but am not sure. I would like an opinion from someone with more...

Hey guys I need a 22 mm mikuni carb for my pitbike I am looking for a genuine mikuni not a chikuni I live in Corona, CA please pm me with a price thanks

I have a comet tav2 30 series that is like new it has about 4 hours of use on it and has a rib cut on the back to fit a honda clone. It comes with everything to use it, the back plate , driven , driver, cover, spacers, belt, and mounting harware. I am asking $130 plus shipping.

I just tried my mini bike with a comet tav2 and it feels like I lost alot of top end and the motor does not rev up as high anymore. It picks up the front end a little on flat ground, and when going up hill on dirt it easily wheelies. Is there any way to increase my top end to make it rev up to...

I have a stretched cat with a tav2 that I need brakes for. It used to have a scrub brake but I removed it due to the excessive tire wear. I built it to hit 50 mph , I bought some chinese 125 quad hydraulic brakes from ebay with plans on mounting it on the rear sprocket. I am having problems with...

I am looking for a 25 to 30 tooth 41 sprocket for a mini bike I have talked to a fellow mini biker before who had one and he said he got it from east LA but did not give me an address does anybody know where in east La I can find a small 41 chain mini bike sprocket? thanks tundrabeagle

My predator 212 is hard to start when it is cold. Every time I start it i need to take out the plug clean it put it back in an pull like crazy. My mods to the engine are a 14 cc head, k&n type air filter, header, and a 90 main jet. It is easy to start when it is hot and runs good . It is just a...

I have a stretched cat mini bike that has a 420 chain rubbing on the motor plate. I tried finding a half link but my local motorcycle shop told me they don't make half links for motorcycle chain. I tried moving the motor up but ran out of room. I was going to use a chain tensioner from a...

I have a predator that wasn't starting until i put a little bit of oil in the spark plug hole. It started right right up until the plug got fouled with oil. According to the manual if it starts with oil in the cylinder it is a compression problem. The head gasket has been reused and is losing...

I am looking for handlebars and forks that will fit a cat that are bent forward a little . I have a set of original cat bars that look good but go straight back not leaving me any room for my legs. I am also willing trade my two cat frames for a bigger mini bike frame one is stretched.

I have a predator 212 that hesitates a little before it begins to accelerate at full throttle. Does this mean that I am running to rich or lean? I cant tell by the spark plug as all my plugs are black from when i lay it down and oil gets into the cylinder.

http://answers.yahoo.com/question/index?qid=20071019000014AA0T8uQ I was hoping to apply this to a predator 212 by sanding the round part of cam maybe .20 on the intake side to get more valve lift. " So when Cam turns around From REDUCED Base Circle Radius,,,and TO the LOBE PEAK,,, The Rocker...

I need a 196cc clone carb looking to pay 10 for the carb plus shipping. I also need a 14cc head or two looking to pay 20 plus shipping for each. Let me know if you have one and how much you are asking please.

I have a vintage 1969 2 hp briggs and stratton motor that has been completely cleaned out and put back together. It has new gaskets and oil. It starts easily and runs very good . It will work good on a mini bike, gokart or anything else that needs a motor.It also comes with a vintage centrifugal...

I have an old cat 300x mini bike that I am trying to figure out what I need to do to get to my 60 mph goal. Right now it has a predator 212 in it that was going to be rejeted with an intake and exhaust. and right now it tops out at about 40mph with a 5 :1 gear ratio and 12.3 in tires. I was...

I need to buy a max torque clutch sprocket #41 chain 10 tooth or more.

Selling a 1969 2 hp briggs that has been cleaned out and put back together. it has new gaskets, oil and starts 1 or 2 pulls and runs great.it comes with a vintage clutch that has a #40 41 420 sprocket and it still works. looking for $130 plus shipping or local pick up i live in the ie , california

I was riding my predator 212 pretty hard for a few hours and then my clutch fell apart. I then assembled the clutch together and welded it to keep it from breaking. i rode it hard again and after a hill climb my clutch fell apart again . this time the outer plate broke and the welds came off. I...