Search results

  1. J

    B.S. motor ID

    what's up with he weld where the low oil shutoff would go.
  2. J

    new engine for a new build.

    I have used cleaner and an ultrasonic cleaning. It doesn't work. This is a simple carb like I had maybe 25 years ago. I want a vintage look somewhat. I am tempted to throw a late 80s carb on and have some fun.
  3. J

    new engine for a new build.

    general pump. a cheap one. it was clear in the window and only halfway up sight glass when I got it.
  4. J

    new engine for a new build.

    pretty sure only an idle circuit. When I take the screw all the way in no change and completely out no difference.
  5. J

    new engine for a new build.

    Hmm I need to open this one up and count the bearings. I have read one and I have read dual bearing. Supposedly mines a nice one since it came with a low oil shutoff. Yeah not wanting a mikuni on it now. Wanting an old look flathead, pulled off a tiller or in mycase pressure washer look...
  6. J

    new engine for a new build.

    I went ahead and wrote off that pump and tossed it. after running it the small amount I did the oil was pushing out and cloudy through the sight glass. The pump was trash.
  7. J

    Burnout challenge!

    ha I sold it. I'm on it. building a new one now.
  8. J

    Burnout challenge!

  9. J

    LED lights series or paralel

    this is true. however since a majority of led either will or will not work only if correct voltage is used being an led they will still drive. but like you said they will each be powered lower until you reach the point where it just physically won't turn on.
  10. J

    LED lights series or paralel

    series can and will work. I usually wire all lights in parallel.
  11. J

    new engine for a new build.

    I have come to my wits end with this carb. I cleaned it again, it runs great wide open. Still at idle it is surging constantly. What would be a good carb to throw on it?
  12. J

    new engine for a new build.

    this is a zero degree tip. it works, but is low on pressure tt9071 pump. your call. https://youtube.com/shorts/PusBCR-pqxk
  13. J

    new engine for a new build.

    I cleaned again. horrible surging. needle in no change needle out and sitting in my hand nothing changes. Boiled in lemon juice and dawn then ultrasonic cleaned. Gonna have to get a new one. Wish I knew which passages went where. I have a feeling it's the smaller one in the bottom where...
  14. J

    Briggd and Stratton Industrial plus

    great info.
  15. J

    Briggd and Stratton Industrial plus

    Are these the same as an I/C engine? This engine was from 1995. I can't find much of anything detailed on Google. Hoping someone knows something about it. I figure steelsleeve and at least 1 bearing but idk. going to try and stick a magnet to check sleeve.
  16. J

    new engine for a new build.

    Well I cleaned again today. will crank and run off choke. However it still surges a little bit when I was testing pump. Idk if it's a fuel issue or what. ibgot the screw close to where it was. Might still be some gunk in the carb. what exactly is an industrial plus engine? same as an...
  17. J

    new engine for a new build.

    sure. if you need some small thing I won't mind shipping. basically removing exhaust intake all boxes and frame etc.
  18. J

    new engine for a new build.

    3/4 shaft on this particular one from 1995. pump is working. Almost tempted to use the pressure washer. maybe a new predator and this pump then flip it. Don't need 2 pressure washers. But 20 bucks couldn't pass it up. Now have 3 flatheads. probably going to sell the 1974 one. Flathead...
Top