Go Back   DIY Go Kart Forum > Building Plans And Advice > Using Tools and Welding

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 09-12-2010, 09:41 AM
KieranM's Avatar
KieranM KieranM is offline
Doin It!!
 
Join Date: Aug 2009
Location: Kilkenny, Ireland
Posts: 1,426
Thanks: 92
Thanked 98 Times in 89 Posts
Default Different types of welding rods and applications

I don't take credit for this, but i though it might be helpful.

6010: Deep penetration with a smooth arc and low spatter. Ideal for use on farm and road equipment, tanks, piping, wrought iron, building structures, jigs, fixtures and general maintenance. DC electrode positive unit must be run on DC welder.

6011: Popular electrode for utility type welders. Works well on rusty, dirty steel. Deep penetration allows for use on bridges, pressure vessels, farm and road equipment, building structures, tanks and pipe. Similar to 6010, but can be used on AC or DC current. Ideal for use on AC welders.

6013LV : Easy operation with a soft arc make it ideal for sheet metal use. Especially poor fitting applications and general repair on light thickness fabrication. AC/DC electrode works well on low cost hobby type welders.

7014: Iron powder coating allows for higher welding speeds and use of a drag technique. Easier to use than most electrodes. AC/DC electrode works well on poor fitting joints and welds requiring a very flat bead.

7018: High quality weld for mild steel makes this the first choice for field construction applications where weld quality is critical. Ideal for carbon steel where cracking is a concern. Keep in a sealed container or an electrode oven when not in use. DC electrode positive.

7018 AC: Designed to operate on AC welders. Easier to operate than most other low hydrogen electrodes. Preferred for its high purity, crack resistant welds on mild and carbon steels.

80LV Red: AC/DC straight or reverse polarity, all position electrode can be used with low voltage machines for short, intermittent or tack welds on thin, medium and heavy sections of mild steel.

252: Welds 310 and 314 stainless subjected to corrosion at elevated temperatures as well as dissimilar steels and stainless of unknown analysis.

275: Produces high tensile and yield strengths on tool, high alloy, string, stainless, aircraft, nickel clad and dissimilar steels.

HY-10: Special high strength electrode is machinable and ideal for joining or build up of low alloy and sulphur steels.

8: Provides a high nickel machinable deposit for welding parts, filling holes and defects and salvaging imperfect castings on thin sections of cast iron. Meets AWS A5.15 Class ENiCl-A.

8-60: Nickel electrode provides machinable deposits with high strength and good ductility for heavy sections of cast iron and ductile iron. Meets AWS A5.15, Class ENiFeCl-A.

6: Provides high strength, dense, sound welds on cast iron where machinability is not needed. Excellent for dirty or grease soaked castings.

4-60:
Straight or reverse polarity electrodes provide strong machinable, crack resistant and spatter free deposits without porosity. Fort heavy sections of cast iron, ductile iron, and dissimilar metals. Will not overheat at rated amperage.

24 AC/DC: AC/DC all position electrode produces sound, porosity-free deposits on bronze, brass, copper, cast iron and steel. Joins dissimilar metals or overlay on cast iron or steel.

34 DC: Premium DC reverse, all position, aluminum electrode for joining, build up, cladding and reinforcing of aluminum sheets, plates and castings of 1/8″ or thicker. Has extruded coating, and leaves dense smooth deposits that provide good color match to base metal.

308L AC/DC: Excellent wetting action and bead appearance makes this all position electrode ideal for welding most types of 18-8 stainless steel (304,302). Deposit is highly resistive to corrosion.

309L AC/DC: Higher corrosion resistance and strength than type 308 make this all position electrode ideal for 304 to 309 and 308 to carbon steels. Excellent weld appearance.


316L AC/DC:
Provides a stable smooth arc and fine spray metal transfer with a uniform bead that is flat or slightly concave with straight edges. Penetration is complete and the weld metal is free from porosity. Also has good out-of-position characteristics. For 316L and 318 type steels in the chemical industry. Maximum of .03% carbon deposit.

308L-17: Used in paper and chemical industries, food processing equipment, dairies, breweries, distilleries, kitchens and hospitals for welding Cr/Ni steels such as 304L, 308L, 301, 303, 304 and 309.

309L-17: AC/DC reverse, all position electrode for welding carbon steels to stainless at service temperatures below 600 degrees Fahrenheit.

316L-17: AC/DC reverse, all position electrode, low-carbon electrode for join 316 and 316L stainless subject to corrosive media.

HS-2C: Hard facing electrode for severe abrasion and moderate impact with hardness 58-62 Rockwell C.


HS-65W:
Hard facing electrode for superior wear resistance involving extreme abrasion with hardness 63-67 Rockwell C.

Ni-Matrix: All position hard facing electrode for constant heavy impact and abrasion with hardness 48 Rockwell C.


Super Join-M:
Hard facing electrode resistant to corrosion from water and mild corrosives with severe impact protection on manganese steel and unknown iron base metals.

Chamfer Rod: AC/DC straight all position gouging electrode for ferrous and non-ferrous metals.

Stud Plus: AC/DC reverse polarity gouging electrode for removing broken studs and bolts.
Reply With Quote
The Following 5 Users Say Thank You to KieranM For This Useful Post:
devino246 (09-12-2010), freakboy (09-12-2010), itsid (10-11-2013), Leftythenub (09-29-2010), slowcal (08-13-2014)
  #2  
Old 09-12-2010, 05:06 PM
freakboy's Avatar
freakboy freakboy is offline
the names 'mater
 
Join Date: May 2009
Location: hick town
Posts: 4,012
Thanks: 134
Thanked 91 Times in 80 Posts
Default

Sticky time!!
__________________
Pardon me, sir gangster! but it apears your pants are declining in elevation!
Reply With Quote
  #3  
Old 09-12-2010, 05:08 PM
devino246's Avatar
devino246 devino246 is offline
Official DIYGK Chem Nerd
 
Join Date: Sep 2009
Location: Lynchburg, VA
Posts: 3,871
Thanks: 270
Thanked 276 Times in 242 Posts
Default

Quote:
Originally Posted by freakboy View Post
Sticky time!!
Second!
__________________
ASE Certified
Reply With Quote
  #4  
Old 10-11-2013, 05:13 PM
machinist@large's Avatar
machinist@large machinist@large is offline
Senior Member
 
Join Date: Jul 2011
Location: West Michigan
Posts: 1,922
Thanks: 1,453
Thanked 271 Times in 221 Posts
Talking

Who do I get to thank for bringing this up front? This is one forum I try to stay abreast of, and I don't remember seeing this thread before ( I joined in mid 2011). To who ever of our moderators who dredged it up and moved it to where it probably should be, WELL DONE!!!

Pat.
Reply With Quote
  #5  
Old 10-12-2013, 12:00 AM
landuse's Avatar
landuse landuse is offline
Moderator
 
Join Date: Nov 2010
Location: Pietermaritzburg, South Africa
Posts: 9,973
Thanks: 600
Thanked 1,297 Times in 1,123 Posts
Default

Quote:
Originally Posted by machinist@large View Post
Who do I get to thank for bringing this up front? This is one forum I try to stay abreast of, and I don't remember seeing this thread before ( I joined in mid 2011). To who ever of our moderators who dredged it up and moved it to where it probably should be, WELL DONE!!!

Pat.
I could be wrong, but I think it had been a sticky for a while. I agree that it is a great thread though.
__________________
Latest Build: http://www.diygokarts.com/vb/showthread.php?t=23363
I got myself a center punch
Reply With Quote
  #6  
Old 10-12-2013, 04:32 AM
fowler's Avatar
fowler fowler is online now
Senior Member
 
Join Date: Nov 2009
Location: Bullsbrook West Aus
Posts: 5,273
Thanks: 60
Thanked 428 Times in 389 Posts
Default

its good as long as u are in the US
non of those numbers meet any Aus numbers

but still
an intresting read
__________________
That's not an oil leak
It's horsepower sweat
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 10:32 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.