Go Back   DIY Go Kart Forum > Building Plans And Advice > Engines & Clutches

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 11-09-2019, 09:38 AM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is offline
Currently flathead-crazed
 
Join Date: Jan 2019
Location: Texas
Posts: 2,491
Thanks: 619
Thanked 327 Times in 299 Posts
Default Check those spark plugs!

Doof.
So a long time ago(in a galaxy far, far away), I pulled the old spark plugs from my 5 HP HiPo Briggs and my 3 HP FrankenBriggs, assuming they were dead.
Recently the thought occurred that maybe the spark plugs were not the reason my engines were not running initially.
The FrankenBriggs needed ignition points servicing, and the HiPo was having some seriously weird carb issues.
So this morning I dug the old beat up spark plugs out of my stash(yes I stored the HiPo one for almost a year), and plugged them into my currently carb-less FrankenBriggs.
And voila!
Clear, strong spark on BOTH plugs!
So don't just assume your plug is the reason your engine won't run!
Now I have two spare plugs!(Oh yeah, the HiPo one was actually a brand name Champion RC-J8 resistor plug)
Lesson learned from me so YOU don't have to!
Good thing I didn't throw them out!
__________________
"(Speed Demon)Speedin' on the freeway, gotta get a leadway..." -Michael Jackson
Reply With Quote
  #2  
Old 11-09-2019, 10:00 AM
Budget GoKart's Avatar
Budget GoKart Budget GoKart is online now
Aka a kenbar
 
Join Date: Dec 2018
Location: indiana
Posts: 973
Thanks: 19
Thanked 101 Times in 94 Posts
Default

I keep mine too LOL
__________________
quotes from me: I didnt do it. i broke it!
Reply With Quote
The Following User Says Thank You to Budget GoKart For This Useful Post:
JTSpeedDemon (11-09-2019)
  #3  
Old Yesterday, 08:29 AM
Kentucky Boy's Avatar
Kentucky Boy Kentucky Boy is offline
Senior Member
 
Join Date: Dec 2015
Location: Bowling Green, KY
Posts: 592
Thanks: 191
Thanked 192 Times in 148 Posts
Default

Maybe you should spend some more time researching and learning instead of giving out endless amounts of advice about stuff you not only have no clue about, but have never even had experience doing yourself. You donít even have the skills or knowledge to properly repair your Briggs and get them running.
Reply With Quote
The Following 4 Users Say Thank You to Kentucky Boy For This Useful Post:
950speed (Yesterday), J.S.@SMS (Today), jeffone (Yesterday), Randy H (Yesterday)
  #4  
Old Yesterday, 08:40 AM
Budget GoKart's Avatar
Budget GoKart Budget GoKart is online now
Aka a kenbar
 
Join Date: Dec 2018
Location: indiana
Posts: 973
Thanks: 19
Thanked 101 Times in 94 Posts
Default

Quote:
Originally Posted by Kentucky Boy View Post
Maybe you should spend some more time researching and learning instead of giving out endless amounts of advice about stuff you not only have no clue about, but have never even had experience doing yourself. You donít even have the skills or knowledge to properly repair your Briggs and get them running.
Who was this aimed at me or jt
__________________
quotes from me: I didnt do it. i broke it!
Reply With Quote
  #5  
Old Yesterday, 10:14 AM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is offline
Currently flathead-crazed
 
Join Date: Jan 2019
Location: Texas
Posts: 2,491
Thanks: 619
Thanked 327 Times in 299 Posts
Default

Quote:
Originally Posted by Kentucky Boy View Post
Maybe you should spend some more time researching and learning instead of giving out endless amounts of advice about stuff you not only have no clue about, but have never even had experience doing yourself. You don’t even have the skills or knowledge to properly repair your Briggs and get them running.
Jeepers, I don't think it really matters WHO that one was aimed at!
I DO have the skills and I DO have the knowledge, I am just limited by money and parts.
And this was just my experience, I just wanted to share, not get shot out of the sky for sharing it. Sure it was stupid, but there's always a chance that someone can learn something from it. And no I am not clueless about these engines(I've revived THREE of them, just one is having ignition and carb issues).
And if it was aimed at BGK, still, that's pretty harsh. We're just some teenagers trying to have fun!
__________________
"(Speed Demon)Speedin' on the freeway, gotta get a leadway..." -Michael Jackson
Reply With Quote
The Following User Says Thank You to JTSpeedDemon For This Useful Post:
Budget GoKart (Yesterday)
  #6  
Old Yesterday, 12:00 PM
Randy H Randy H is offline
Senior Member
 
Join Date: Oct 2016
Posts: 882
Thanks: 816
Thanked 456 Times in 358 Posts
Default

^
Kentucky Boy is absolutely right. You continually post about things you have little knowledge of, and less experience. You are in a learning stage.
You post about using hammers to remove flywheels, I could go on and on. I get it, your young and you don't even know you don't know.
Slow down, learn, get some real experience, your lucky you got this last engine running, very lucky.
Reply With Quote
The Following User Says Thank You to Randy H For This Useful Post:
jeffone (Yesterday)
  #7  
Old Yesterday, 12:37 PM
Tpdingo Tpdingo is offline
Senior Member
 
Join Date: Nov 2017
Location: Bellmore, NY
Posts: 878
Thanks: 13
Thanked 249 Times in 211 Posts
Default

I think I'd take a middle ground on this....what JT said wasn't necessarily useless information, but JT, I would take a more of a "this is what i experienced" than a "this is what YOU should do" when you write stuff like this.
__________________
Give a wrench long enough and WD-40, and I can remove the world's rusty bolts.
Reply With Quote
  #8  
Old Yesterday, 12:42 PM
jeffone jeffone is offline
Junior Member
 
Join Date: Jul 2019
Location: Alabama
Posts: 20
Thanks: 5
Thanked 2 Times in 2 Posts
Default

JT You really should stop spending all your time typing on the key board. If you would put that much time in learning how to work on your go karts you might have something worth typing about.
Reply With Quote
  #9  
Old Yesterday, 01:29 PM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is offline
Currently flathead-crazed
 
Join Date: Jan 2019
Location: Texas
Posts: 2,491
Thanks: 619
Thanked 327 Times in 299 Posts
Default

Jeepers, didn't mean to start an argument....
About the hammers on flywheels: Guess what?? Here's what the OFFICIAL Briggs and Stratton manual says!!:
Quote:
1. Support flywheel with a gloved hand or a shop ragwhile exerting an upward pull.
2. Strike outside rim of flywheel with a soft facedhammer using a sharp blow.
Ok sure, I used a hard hammer, but I TRIED the soft faced one and it didn't work.
My flywheels do NOT have holes for a puller. What I did, I had to do, and it worked.
All I wanted to point out with this thread is that it's a good idea to save parts because they might still be good.
I DID NOT want criticism on my methods OR the fact that I try to help people on the forum. Sometimes I see threads where literally NO ONE replies with anything useful. That happened when I asked a long time ago for help with the Briggs starter. No useful information.

Quote:
Originally Posted by Kentucky Boy View Post
You don’t even have the skills or knowledge to properly repair your Briggs and get them running.
THAT is just straight up untrue and hurtful. Completely wrong.

Y'all can keep making fools of yourselves, I don't care. I'd rather be the victim than the culprit.
Quote:
Originally Posted by Most of the DIY Go Kart Forum
Stop giving advice. You're young and dumb.
__________________
"(Speed Demon)Speedin' on the freeway, gotta get a leadway..." -Michael Jackson
Reply With Quote
  #10  
Old Yesterday, 01:31 PM
950speed's Avatar
950speed 950speed is offline
Senior Member
 
Join Date: Jun 2018
Location: Liberty Hill, Texas
Posts: 363
Thanks: 71
Thanked 41 Times in 38 Posts
Default

Maybe this isn’t what you WANTED, but rather what you NEEDED

These guys probably are older than you and have experienced more than you.
Reply With Quote
  #11  
Old Yesterday, 04:19 PM
jeffone jeffone is offline
Junior Member
 
Join Date: Jul 2019
Location: Alabama
Posts: 20
Thanks: 5
Thanked 2 Times in 2 Posts
Default

Not trying to be mean or anything I didn't mean to if that's the way it sounded just pointing something out
Reply With Quote
The Following User Says Thank You to jeffone For This Useful Post:
JTSpeedDemon (Yesterday)
  #12  
Old Yesterday, 04:22 PM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is offline
Currently flathead-crazed
 
Join Date: Jan 2019
Location: Texas
Posts: 2,491
Thanks: 619
Thanked 327 Times in 299 Posts
Default

Ok oops. No hard feelings then!
But yeah, it's hard to find these obscure parts. Especially for a reasonable price.
And we still need a decent set of drill bits, so that severely hampers productivity.
__________________
"(Speed Demon)Speedin' on the freeway, gotta get a leadway..." -Michael Jackson
Reply With Quote
  #13  
Old Yesterday, 07:55 PM
Budget GoKart's Avatar
Budget GoKart Budget GoKart is online now
Aka a kenbar
 
Join Date: Dec 2018
Location: indiana
Posts: 973
Thanks: 19
Thanked 101 Times in 94 Posts
Default

This dude I know he is helping me fix up my yerfdog a Lil bit. keeps everything and uses what he has instead of just getting everything new. Like some people... some people buy everything new because they don't care about used or old stuff because "it's a waste of time and money" that's the fun in this hobby, learning and having fun while doing it. Not just craming a bunch of new shiny parts on some already restored go kart. Fun and learning takes old junk trying to fix it failing and trying again and again till you fixed it and learned something. I've done it and I'm sure most others on here have too.
Just some people just prefer buying something new and spending 1k on upgrade parts and barely knowing how to install them. And when you figure it out your "experienced enough to talk some random person down for learning". Sorry about my rant, I'm going to bed.
__________________
quotes from me: I didnt do it. i broke it!
Reply With Quote
  #14  
Old Yesterday, 07:56 PM
Dingocat's Avatar
Dingocat Dingocat is offline
Broke
 
Join Date: Apr 2018
Location: Cleveland Ohio
Posts: 401
Thanks: 33
Thanked 82 Times in 67 Posts
Default

I see this like the situation with the bottom of my dingi. Everything is pitted. People on here say that I should probably replace it. I'll concider that and if I bend or break the offending piece I'll go huh. Probably should have listened. It's about learning. Like knowing thay a chain that is loose with the kart on the ground and tight with it in the air isn't nessicarily bearings.
__________________
Current Manco hoarder
Reply With Quote
  #15  
Old Today, 06:54 AM
J.S.@SMS's Avatar
J.S.@SMS J.S.@SMS is online now
Here 8am-? Mon-Fri
 
Join Date: Sep 2018
Location: Weeki Wachee Fl.
Posts: 571
Thanks: 61
Thanked 104 Times in 91 Posts
Default

Quote:
Originally Posted by Kentucky Boy View Post
Maybe you should spend some more time researching and learning instead of giving out endless amounts of advice about stuff you not only have no clue about, but have never even had experience doing yourself. You donít even have the skills or knowledge to properly repair your Briggs and get them running.
Sorry about joining in late, but all I have to say about this statement is... BURN!.

And Budget, if you're getting on people for replacing parts on their engines, then don;t leave out JT. Remember he just swapped the rod on his 5hp. And also, sometimes the best thing to do is replace parts. Like the engine in the truck my uncles about to give me. I'm going to put in a new rotating assembly (crank, rods, pistons, bearings, and rings), swap in a better cam, add retrofit roller lifters, new rockers, new valve springs and retainers, upgraded distributor and possibly a crank trigger, and have the head and block cleaned up. Why you ask, because it's a 1978 windsor 351 with 250 thousand miles on it. That engine made about 146hp factory, and the probably 125 it has now won't move a sleeper.
__________________
If a picture is worth a thousand words, then how about a video?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 07:26 AM.