Go Back   DIY Go Kart Forum > Building Plans And Advice > Photo Gallery & Project Log

Notices

Reply
 
Thread Tools Display Modes
  #41  
Old 02-22-2020, 11:36 PM
gegcorp2012's Avatar
gegcorp2012 gegcorp2012 is offline
Senior Member
 
Join Date: Jun 2019
Location: Alabama
Posts: 191
Thanks: 14
Thanked 41 Times in 37 Posts
Default

Quote:
Originally Posted by Stew View Post
...That front grill including the Ford script is one big sticker, I found a Ford script that will go nicely, still not sure how I'm going to recreate that grill effect with paint though.


Remember some of the custom paint from the 60s and 70s (vans, etc) where they used to spray lace patterns ? I think they sprayed the lighter color first (aluminum or gold or your preference for the grille color), then clear, and after drying they put on the mask layer (an actual piece of lace, or expanded wire mesh in your case) then fog it sparingly with the darker color.

If it comes out to your liking, add a coat of clear to protect your work it and give it some depth.

BTW, I am NOT a paint guy, but having tried a similar thing, I would suggest practicing on something first (slick side of poster board) oriented the same way you plan to paint the grille,, and keep the spray light when applying the background color through the mesh (or lace) so you get a sharp pattern without runs.

Your project is looking good! Nice work !!





Sent from my SM-J700T using Tapatalk
Reply With Quote
  #42  
Old 02-24-2020, 06:49 PM
Stew Stew is offline
Member
 
Join Date: Dec 2019
Posts: 40
Thanks: 7
Thanked 17 Times in 13 Posts
Default

gegcorp2012 I was thinking of something along those lines also, and yep I will definitely practice first!

The seat came today so I was able to make a mount and get that finished. Here is the seat mounting setup for the original seat, where ever that is.


I cut that off, cleaned up the old welds and made a bracket out of 1x1x1/8 angle iron


And here is the seat mounted. The cushions are not snapped down yet, the green upholstery will tie into the paint scheme for the body.


It's actually a boat seat from Amazon and folds down which is perfect because once the body is mounted that will really help with access to the pull start. Also I mounted it a little further back than the original seat, every little bit of leg room helps!


And finally I made a little dashboard for the tach/hour meter and engine stop switch
Reply With Quote
  #43  
Old 02-24-2020, 06:52 PM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is online now
2019 Build Off Winner!
 
Join Date: Jan 2019
Location: Texas
Posts: 3,403
Thanks: 774
Thanked 523 Times in 476 Posts
Default

I wouldn't put the kill switch there. To have to reach through the steering wheel to cut the engine, well, I see too many possible wrecks.
__________________
Currently Flathead-Crazed
Reply With Quote
  #44  
Old 02-24-2020, 07:24 PM
Stew Stew is offline
Member
 
Join Date: Dec 2019
Posts: 40
Thanks: 7
Thanked 17 Times in 13 Posts
Default

Yeah reaching through the steering wheel wouldn't be the best idea. It may not look like it but if I mount the switch on the right side of the dash, because I'm right handed ya know, then moving your hand from the steering wheel around to the switch is a pretty quick motion, I was testing it out to make sure.
Reply With Quote
  #45  
Old 02-24-2020, 08:46 PM
gegcorp2012's Avatar
gegcorp2012 gegcorp2012 is offline
Senior Member
 
Join Date: Jun 2019
Location: Alabama
Posts: 191
Thanks: 14
Thanked 41 Times in 37 Posts
Default

@stew ,
That boat seat seems like a great idea, especially that it folds to give access to the rip cord.

I love to see original ideas like that.

BTW... on the grille, did you consider upgrading to a real grille to match your real Ford logo ? A screen window frame and a piece of expanded mesh would be easy to make the right size since the target shape is pretty square. If you can find those pieces cheap, and are able to make some hacksaw 45 degree cuts to the screen frame, it would add a classy touch of authenticity. Bonus points in the looks department if you add a piece of brass kick plate to simulate the top radiator tank.

Sent from my SM-J700T using Tapatalk
Reply With Quote
  #46  
Old 02-25-2020, 05:42 AM
Budget GoKart's Avatar
Budget GoKart Budget GoKart is online now
Aka a kenbar
 
Join Date: Dec 2018
Location: indiana
Posts: 1,427
Thanks: 42
Thanked 159 Times in 149 Posts
Default

I learned something from a race kart frame builder he says, always have your kill switch where you push it down to turn the engine off. because its quicker than pushing it up. also have it to where if the thottle is stuck you can quickly slap it down and it turns off. Jim white told me that he used to make race karts and travel alot. So he has seen many wrecks.
__________________
I gotta fix my flathead collection
Reply With Quote
  #47  
Old 02-25-2020, 09:39 AM
Stew Stew is offline
Member
 
Join Date: Dec 2019
Posts: 40
Thanks: 7
Thanked 17 Times in 13 Posts
Default

gegcorp2012 If I'm being honest the boat seat wasn't my idea, I ran across the idea elsewhere, and in fact in the customer reviews on Amazon a guy had a picture of him using them on his golf cart! I did kick around ideas about cutting out an opening to make a realistic grill, and that is still on the table.

Budget GoKart those are great points.

I test drove it with the heavy body on a few days ago and found it has another built in way to quickly scrub off speed in an emergency, with the live axle and grippy tires and 3 hp motor just stop going in a straight line

In all seriousness though the stop switch will be nearly at my fingertips quickly accessible in an emergency.
Reply With Quote
  #48  
Old 02-27-2020, 07:06 PM
Stew Stew is offline
Member
 
Join Date: Dec 2019
Posts: 40
Thanks: 7
Thanked 17 Times in 13 Posts
Default

Got a few more things done.

After getting the seat mounted I could check for clearance between the seat and inside of the body for bracing the rear body mount. I ran 3/4" square tubing from the rear body mount down to the side body mount.


Next I cut out the floor pan because I wanted it to be removable because... well just because haha.


Here it is cut out, nasty. Actually I wanted it removable so I could clean it up good for repainting. With it welded in place I couldn't get to the area between the floor pan and tube frame.


I welded in six tabs to bolt it in and after trimming off the jagged edges of the floor pan it fits good.


Next I cut off the spindle arms that I had recently re-welded on because they were so short that the steering was just way too twitchy. I made longer ones to slow the steering down but still need to weld them back in. They look really long next to the really short ones but really they are a normal length.


And finally I made front and rear bumpers. If you look at pictures of Model T bumpers a lot of them are a 'double bar' style, I made these to resemble that and with the body on they look pretty good.



The frame is almost done!
Reply With Quote
The Following 2 Users Say Thank You to Stew For This Useful Post:
Flyinhillbilly (02-27-2020), landuse (02-27-2020)
  #49  
Old 03-12-2020, 11:47 AM
Stew Stew is offline
Member
 
Join Date: Dec 2019
Posts: 40
Thanks: 7
Thanked 17 Times in 13 Posts
Default

More progress

Here is the revised spindle arm/steering geometry, this slowed the steering response down noticeably. I haven't test driven it yet but when working the steering wheel back and forth this feels MUCH better.


I also made steering stops


That floor pan? Well after scrubbing off what looked like some kind of aerosol can undercoating with gasoline, and taking a wire wheel to it I gave it a muriatic acid soaking to get rid of the rest of the rust.


And finally after some work with the angle grinder with wire wheel the frame is hanging from the hoist ready for some paint.
Reply With Quote
The Following User Says Thank You to Stew For This Useful Post:
landuse (03-13-2020)
  #50  
Old 03-21-2020, 07:35 PM
Stew Stew is offline
Member
 
Join Date: Dec 2019
Posts: 40
Thanks: 7
Thanked 17 Times in 13 Posts
Default

And the frame is painted and put back together!



I just did a couple test laps around the neighborhood and it's running good, with a lot of people at home these days there have been a few mini bikes and atv's doing laps around the neighborhood

Now it's time to get working on that fiberglass body
Reply With Quote
  #51  
Old 03-22-2020, 07:27 PM
gegcorp2012's Avatar
gegcorp2012 gegcorp2012 is offline
Senior Member
 
Join Date: Jun 2019
Location: Alabama
Posts: 191
Thanks: 14
Thanked 41 Times in 37 Posts
Default

Really neat looking !


Sent from my SM-J700T using Tapatalk
Reply With Quote
  #52  
Old 03-22-2020, 09:04 PM
Whitetrashrocker's Avatar
Whitetrashrocker Whitetrashrocker is offline
Inmate #952016
 
Join Date: Sep 2016
Location: Southern New Mexico
Posts: 2,177
Thanks: 319
Thanked 833 Times in 647 Posts
Default

Again. Digging the build. Waiting for the body.

How's the steering with the short pitman and long spindle arms?
__________________
Think for yourself, Question authority.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 11:29 AM.