Go Back   DIY Go Kart Forum > Building Plans And Advice > Go Kart Discussion

Notices

Reply
 
Thread Tools Display Modes
  #21  
Old 01-02-2020, 08:39 AM
rushking19's Avatar
rushking19 rushking19 is offline
Senior Member
 
Join Date: Jun 2012
Location: Richmond Virginia
Posts: 1,045
Thanks: 97
Thanked 82 Times in 79 Posts
Default

Quote:
Originally Posted by JTSpeedDemon View Post
That could almost be the next viral meme!
Lol I wish it could be
__________________
It's Fast ,But Needs One More Cylinder
Reply With Quote
  #22  
Old 01-02-2020, 11:21 AM
MrC. MrC. is offline
Senior Member
 
Join Date: Jun 2016
Location: florida
Posts: 239
Thanks: 10
Thanked 51 Times in 49 Posts
Default

You gotta video a full throttle launch.
or a burn out with wheelie, you know you want to see that too.
after that race a Lamborghini, and win!

Awesome build.
MrC.
Reply With Quote
  #23  
Old 01-02-2020, 12:27 PM
rushking19's Avatar
rushking19 rushking19 is offline
Senior Member
 
Join Date: Jun 2012
Location: Richmond Virginia
Posts: 1,045
Thanks: 97
Thanked 82 Times in 79 Posts
Default

Quote:
Originally Posted by MrC. View Post
You gotta video a full throttle launch.
or a burn out with wheelie, you know you want to see that too.
after that race a Lamborghini, and win!

Awesome build.
MrC.
Definitely will get more videos, it does wheelies not big ones but it does it tried to get it on video but didn't but it pulls hard
__________________
It's Fast ,But Needs One More Cylinder
Reply With Quote
  #24  
Old 01-02-2020, 12:31 PM
JTSpeedDemon's Avatar
JTSpeedDemon JTSpeedDemon is offline
2019 Build Off Winner!
 
Join Date: Jan 2019
Location: Texas
Posts: 3,538
Thanks: 796
Thanked 548 Times in 498 Posts
Default

Do you plan to make an expansion pipe setup for this beast??
Or are you scared of death?

__________________
Currently Flathead-Crazed
Reply With Quote
  #25  
Old 01-02-2020, 01:21 PM
rushking19's Avatar
rushking19 rushking19 is offline
Senior Member
 
Join Date: Jun 2012
Location: Richmond Virginia
Posts: 1,045
Thanks: 97
Thanked 82 Times in 79 Posts
Default

Quote:
Originally Posted by JTSpeedDemon View Post
Do you plan to make an expansion pipe setup for this beast??
Or are you scared of death?

Not really because there wasn't really an expansion chamber for this year rotax 399cc, if I wanted one I would have to go custom mostly to fit the go kart which would cost a lot
__________________
It's Fast ,But Needs One More Cylinder
Reply With Quote
  #26  
Old 03-26-2020, 07:24 PM
rushking19's Avatar
rushking19 rushking19 is offline
Senior Member
 
Join Date: Jun 2012
Location: Richmond Virginia
Posts: 1,045
Thanks: 97
Thanked 82 Times in 79 Posts
Default

Finally got some mufflers on this thing , but they barely quite it down lol, but its a little bit quieter, it has twin rlv mufflers on it expected it to change the tone bit its still pretty much the same but they do look good
Attached Thumbnails
20200326_191459.jpg  
__________________
It's Fast ,But Needs One More Cylinder
Reply With Quote
  #27  
Old 03-26-2020, 07:29 PM
rushking19's Avatar
rushking19 rushking19 is offline
Senior Member
 
Join Date: Jun 2012
Location: Richmond Virginia
Posts: 1,045
Thanks: 97
Thanked 82 Times in 79 Posts
Default

https://youtu.be/vz5awswWDqY
__________________
It's Fast ,But Needs One More Cylinder
Reply With Quote
  #28  
Old 04-06-2020, 06:50 PM
rushking19's Avatar
rushking19 rushking19 is offline
Senior Member
 
Join Date: Jun 2012
Location: Richmond Virginia
Posts: 1,045
Thanks: 97
Thanked 82 Times in 79 Posts
Default

Well I have a new record on this thing I went 65 mph on this death trap it actually feels pretty safe and but scary at the same time this is a really fun go kart , was fun till I broke the crappy welds I did rear motor plate all those years back ,motor is back off rn getting fixed
Attached Thumbnails
20200405_130751.jpg   20200406_144705.jpg  

20200406_144659.jpg  
__________________
It's Fast ,But Needs One More Cylinder
Reply With Quote
  #29  
Old 04-07-2020, 09:46 AM
7thofa2nd's Avatar
7thofa2nd 7thofa2nd is offline
Senior Member
 
Join Date: Jun 2018
Location: Barberton, OH
Posts: 104
Thanks: 18
Thanked 13 Times in 11 Posts
Default

Give us a better video.
Reply With Quote
  #30  
Old 04-07-2020, 12:57 PM
Bansil's Avatar
Bansil Bansil is offline
Senior Member
 
Join Date: Apr 2019
Location: Mnts of the farthest NE TN you can go
Posts: 338
Thanks: 14
Thanked 85 Times in 66 Posts
Default

Quote:
Originally Posted by 7thofa2nd View Post
Give us a better video.
X2

That is crazy
Reply With Quote
  #31  
Old 04-09-2020, 01:02 PM
rushking19's Avatar
rushking19 rushking19 is offline
Senior Member
 
Join Date: Jun 2012
Location: Richmond Virginia
Posts: 1,045
Thanks: 97
Thanked 82 Times in 79 Posts
Default

Quote:
Originally Posted by 7thofa2nd View Post
Give us a better video.
I will maybe this weekend rn its being finished up at the shop welding
__________________
It's Fast ,But Needs One More Cylinder
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 12:58 PM.