Go Back   DIY Go Kart Forum > Building Plans And Advice > Photo Gallery & Project Log

Notices

Closed Thread
 
Thread Tools Display Modes
  #1  
Old 05-05-2012, 10:30 PM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default Baja Dune 6.5 Go Kart Restore

My grandpa has had this kart sitting in his backyard for some time now because the motor on it had seized. I decided while I build up funds and parts to build my other kart I was going to get this one running again. I bought a 212cc predator engine for it. The clutch is rusted to the old engine and I can't seem to get it off so I was thinking of just replacing it. I will also need to replace the chain and one of the tubes for the tire. I'm looking to get everything running by the end of this week and then I'm going to sand blast the frame and powder coat. Here's some pics:

The first pic isn't mine it is what it looked like before my gpa removed the roll cage.
Attached Images
File Type: jpg gokart8.jpg (109.9 KB, 31 views)
File Type: jpg gokart7.jpg (132.2 KB, 27 views)
File Type: jpg gokart6.jpg (134.5 KB, 31 views)
File Type: jpg gokart5.jpg (149.7 KB, 29 views)
File Type: jpg gokart4.jpg (145.5 KB, 35 views)
File Type: jpg gokart2.jpg (96.2 KB, 31 views)
File Type: jpg gokart1.jpg (123.9 KB, 29 views)
File Type: jpg 0302111644_0001.jpg (35.2 KB, 42 views)
  #2  
Old 05-06-2012, 02:10 AM
bighead's Avatar
bighead bighead is offline
Senior Member
 
Join Date: Mar 2010
Location: Pacific Northwest USA
Posts: 4,022
Thanks: 158
Thanked 312 Times in 278 Posts
Default

Sweet, Yah just buy a clutch with the same amount of teeth and the correct shaft size. Do you have the cage? I like the seat belts on this kart.
__________________
Attention Criminals!! This is a defense free crime zone. All law-abiding citizens have been disarmed for your convenience.
  #3  
Old 05-06-2012, 06:15 AM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

No, don't have the cage anymore. I was told it made it difficult to get into the kart so that's why it was removed.
  #4  
Old 05-07-2012, 04:12 AM
landuse's Avatar
landuse landuse is offline
Moderator
 
Join Date: Nov 2010
Location: Pietermaritzburg, South Africa
Posts: 17,229
Thanks: 2,058
Thanked 3,408 Times in 2,777 Posts
Default

Nice. You will have it going in no time
The Following User Says Thank You to landuse For This Useful Post:
rcarteraz07 (05-07-2012)
  #5  
Old 05-07-2012, 08:09 PM
cumminsbayou4x4's Avatar
cumminsbayou4x4 cumminsbayou4x4 is offline
Senior Member
 
Join Date: Apr 2012
Location: fairhope alabama
Posts: 829
Thanks: 7
Thanked 34 Times in 32 Posts
Default

go to tractor supply and get a clucth chain and a tube or just slime that will work
  #6  
Old 05-07-2012, 08:41 PM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

I'm wondering about the clutch. I need one that will work with the 212cc predator. The one that was on the old engine looks to be held in place by these rings. All the ones I see online say a bolt and set screws so I'm not sure exactly what I need to get. Any pointers?
  #7  
Old 05-08-2012, 01:06 AM
landuse's Avatar
landuse landuse is offline
Moderator
 
Join Date: Nov 2010
Location: Pietermaritzburg, South Africa
Posts: 17,229
Thanks: 2,058
Thanked 3,408 Times in 2,777 Posts
Default

If you have a threaded hole in your crank, you can pretty much get any clutch. Most of them attach using bolts and set screws. Has your engine got a threaded crank. If not, you can always drill and tap
  #8  
Old 05-08-2012, 09:55 AM
cumminsbayou4x4's Avatar
cumminsbayou4x4 cumminsbayou4x4 is offline
Senior Member
 
Join Date: Apr 2012
Location: fairhope alabama
Posts: 829
Thanks: 7
Thanked 34 Times in 32 Posts
Default

get one from tractor supply thats whats on my preadtor they are 50 dollors and they have a 10 tooth 45 chain one and a 13 tooth 35 chain one both fit on a 3/8 shaft like on the predator then go find a screw for it in there to you could get the old clucth off the old motor by use in a puller or useing cut up 2by4s put the 2by4 pieces behind the clucth and take a rail road spike and hammer it in
  #9  
Old 05-10-2012, 05:49 PM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

So good news!! Got the clutch off the old engine finally! Took some break free and some wiggling but finally got it off. Went through it and it appears to function properly. It was held on by snap rings. They were a pain.. literally. Sliced my knuckle trying to get them off lol. Alls well though. Trip to the go kart shop tomorrow to pick up a new chain and two inner tubes and I should he riding it tomorrow!
  #10  
Old 05-15-2012, 12:20 PM
anderkart's Avatar
anderkart anderkart is offline
Moderator
 
Join Date: Apr 2009
Location: Surprise Arizona USA
Posts: 6,102
Thanks: 495
Thanked 1,159 Times in 960 Posts
Default

Quote:
Originally Posted by rcarteraz07 View Post
Trip to the go kart shop tomorrow to pick up a new chain and two inner tubes and I should he riding it tomorrow!
If your shopping at Dave's karts and cycles in Phoenix, be prepared to get way-overcharged for the lowest quality parts available, plus treated rudely to boot.

This kart shop is a much better source for funkart parts in the valley: http://www.roysgo-karts.com/
The Following User Says Thank You to anderkart For This Useful Post:
rcarteraz07 (05-15-2012)
  #11  
Old 05-10-2012, 06:21 PM
souperman000's Avatar
souperman000 souperman000 is offline
Senior Member
 
Join Date: Dec 2011
Location: Westlake Village, CA
Posts: 2,466
Thanks: 38
Thanked 224 Times in 212 Posts
Default

I picked up a pair of snap ring pliers at a HF parking lot sale for a couple bucks. Havent tried em yet. Snap rings are a pain in the a$$
__________________
It's hard to help people that won't help themselves.
  #12  
Old 05-10-2012, 06:26 PM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

Had a pair of them but they were older and not working very well. That's how I sliced my knuckle. It slipped off and my finger went flying lol.
  #13  
Old 05-11-2012, 09:27 PM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

For it running finally!! It runs pretty good too! GPS had it at 25 mph which is pretty awesome considering I'm 300 lbs!! Lol. Now I just need to come up with a clutch/chain cover since the plastic one it had was melted from before. Ruined my white shirt today from grease and dirt lol. Had to stop riding because some cops went down the street to a house nearby! Lol don't need a ticket! Once I get a new job I'm going to extend the frame(i'm just a little too tall lol) then sandblast and powder coat it.

  #14  
Old 05-11-2012, 09:39 PM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

Oh and get a be seat cover! Lol
  #15  
Old 05-14-2012, 02:50 AM
landuse's Avatar
landuse landuse is offline
Moderator
 
Join Date: Nov 2010
Location: Pietermaritzburg, South Africa
Posts: 17,229
Thanks: 2,058
Thanked 3,408 Times in 2,777 Posts
Default

I'm glad you got her running
  #16  
Old 05-14-2012, 07:55 AM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

Yeah, been riding it pretty hard. Got the whole family on it too! They all love it which is good. The tires there were on it were pretty sun rotter I guess. They started coming apart. Had to replace one and another blew yesterday so it's currently out of commission. I plan on going over to the go kart shop today and getting some new tires as long as they aren't priced too high. If they are I will just order them online.

I was wondering though. Currently the tires are 4.10/3.50-4. Could I get new wheels and tires that are 6" that have the same 3 bolt pattern to give a little more clearance? Would this affect the gearing too much cuz I would like to keep the same speed and acceleration. Or would I have to get a new sprocket and clutch?
  #17  
Old 05-14-2012, 07:59 AM
landuse's Avatar
landuse landuse is offline
Moderator
 
Join Date: Nov 2010
Location: Pietermaritzburg, South Africa
Posts: 17,229
Thanks: 2,058
Thanked 3,408 Times in 2,777 Posts
Default

Your gearing will be affected somewhat, just because the tyres are larger. I cannot remember what your gearing was, but it shouldn't be too much of a change though
  #18  
Old 05-14-2012, 08:04 AM
Doc Sprocket's Avatar
Doc Sprocket Doc Sprocket is offline
*********
 
Join Date: Jun 2009
Location: Ontario, Canada
Posts: 15,677
Thanks: 723
Thanked 2,202 Times in 1,692 Posts
Default

Here's a quick rule of thumb. Measure the total diameter of your tires. Let's say they measure 12". Now, add 10 % (1.2"), so you're fairly safe going to a tire that measures 13.2". This is of course assuming your gear ratio is appropriate in the first place.
__________________
Treat it as you would an aircraft frame and you should have no problems. -Name Withheld
The Manual- "Just the manufacturer's opinion of how to put this together."- Tim "The Tool Man" Taylor
Put down the wrench, and come out with your hands up!- Me!
Wrench, Wheel, Wreck, Repeat...
  #19  
Old 05-14-2012, 07:56 PM
rcarteraz07 rcarteraz07 is offline
Senior Member
 
Join Date: Mar 2012
Location: Phoenix, AZ
Posts: 214
Thanks: 28
Thanked 11 Times in 11 Posts
Default

So I want to come up with some sort of fenders for this. Not only to avoid the rocks that get thrown at me but also my legs hitting the wheels. I got this yesterday and it wasnt too fun!
Attached Images
File Type: jpg imageutd.jpg (303.3 KB, 5 views)
  #20  
Old 05-15-2012, 12:50 AM
landuse's Avatar
landuse landuse is offline
Moderator
 
Join Date: Nov 2010
Location: Pietermaritzburg, South Africa
Posts: 17,229
Thanks: 2,058
Thanked 3,408 Times in 2,777 Posts
Default

Ouch!! How did you get your leg so close to the wheel?
Closed Thread

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 06:36 PM.