Go Back   DIY Go Kart Forum > Building Plans And Advice > Using Tools and Welding

Notices

Reply
 
Thread Tools Display Modes
  #1  
Old 08-18-2019, 06:43 AM
Dat1Guy Dat1Guy is offline
Day1Guy
 
Join Date: Jul 2019
Location: Michigan
Posts: 38
Thanks: 6
Thanked 8 Times in 6 Posts
Default

I've gone and broke my front driver's side spindle that holds the tire. My question is will a wire welder be strong enough to hold this together?

Another pic.
Attached Thumbnails
20190818_083944.jpg   20190818_083953.jpg  

Reply With Quote
  #2  
Old 08-18-2019, 08:01 AM
Kartorbust's Avatar
Kartorbust Kartorbust is offline
Senior Member
 
Join Date: Feb 2016
Location: Lincoln, NE
Posts: 2,754
Thanks: 593
Thanked 744 Times in 626 Posts
Default

As long as the metal is clean and your settings are correct, wire feed welding is strong for that repair. Though putting a bevel groove all around will help get more filler in there to make a stronger weld.
__________________
In the age of information, ignorance is a choice.
Reply With Quote
  #3  
Old 08-18-2019, 09:33 AM
itsid's Avatar
itsid itsid is online now
Moderator
 
Join Date: Jul 2013
Location: Ruhrpott [Germany]
Posts: 10,096
Thanks: 1,382
Thanked 4,258 Times in 3,197 Posts
Default

if you can weld from the rear as well
(can't tell if that's a U-profile or rectangular tubing)

'sid
__________________
Jokes about german sausage are the wurst.
Reply With Quote
  #4  
Old 08-18-2019, 10:20 AM
Dat1Guy Dat1Guy is offline
Day1Guy
 
Join Date: Jul 2019
Location: Michigan
Posts: 38
Thanks: 6
Thanked 8 Times in 6 Posts
Default

Thank you both. It is rectangular so no welding from the back.
Reply With Quote
  #5  
Old 08-18-2019, 11:22 AM
mckutzy mckutzy is offline
Senior Member
 
Join Date: May 2008
Location: bc, canada
Posts: 7,355
Thanks: 815
Thanked 1,755 Times in 1,449 Posts
Default

This is not so much about the method, as how good is your skill in the both...
If you can wire it better... then do so... if not smaw...
__________________
10yr+ club..... My current ride- http://www.diygokarts.com/vb/showthread.php?t=5461
Reply With Quote
  #6  
Old 08-18-2019, 02:29 PM
Dat1Guy Dat1Guy is offline
Day1Guy
 
Join Date: Jul 2019
Location: Michigan
Posts: 38
Thanks: 6
Thanked 8 Times in 6 Posts
Default

Beginner.....I'll try it and if it fails I'll buy a new one. Nothing ventured nothing gained and I'll get a bit more experience with the welder.
Reply With Quote
  #7  
Old 08-18-2019, 04:39 PM
anickode's Avatar
anickode anickode is offline
Senior Member
 
Join Date: Apr 2010
Location: S.E. Michigan
Posts: 1,781
Thanks: 59
Thanked 791 Times in 546 Posts
Default

If you're using a small welder (especially a 120v one), preheating the weld area with a torch (even a propane one) will help. Another thing that can help is to grind all the old weld material off and put a 1/4" chamfer on the spindle, then do a multi pass weld.

Edit: upon looking a little closer at the picture, it does appear that the base metal failed rather than the weld. Rewilding that piece back in to the same hole is more likely to fail again without reinforcement.
__________________
"Well that would be a bomb."
Reply With Quote
  #8  
Old 08-27-2019, 08:10 PM
mrdeadman1 mrdeadman1 is offline
Senior Member
 
Join Date: Jun 2014
Location: Lawrence area, Kansas
Posts: 127
Thanks: 3
Thanked 15 Times in 14 Posts
Default

just order a new spindle from bmi. better safe than sorry
Reply With Quote
  #9  
Old 09-10-2019, 04:09 PM
BullyBike BullyBike is offline
Junior Member
 
Join Date: Sep 2019
Posts: 4
Thanks: 1
Thanked 0 Times in 0 Posts
Default Flux core

Stick electrodes are flux core, and many entry level auto feed welders are also flux core (FCaw).
Generally FCaw has better penetration then solid core MIG or TIG wire.

Definately bevel the part to make a space to build a bead.
Spot it up and then run a thick weld around each side.
Maybe machine a collar and really strengthen that part, better than a new one that might break in a similar way!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 04:51 AM.