Go Back   DIY Go Kart Forum > Search Forums

Notices

Showing results 1 to 12 of 12
Search took 0.00 seconds.
Search: Posts Made By: Gunnar
Forum: Using Tools and Welding 12-02-2007, 06:45 AM
Replies: 3
Views: 2,134
Posted By Gunnar
I have access to arc welder to, but it`s harder...

I have access to arc welder to, but it`s harder to get good welds on it. It`s more difficult to adjust the power and it`s difficult to get a solid weld on angled surface. I mostly use the MiG cus...
Forum: Using Tools and Welding 12-01-2007, 03:53 PM
Replies: 23
Views: 3,524
Posted By Gunnar
I use Argon with CO2 and Nitrogenmonocside for...

I use Argon with CO2 and Nitrogenmonocside for steel and iron welding. it gets the job done and gives nice and smooth welds, but I don`t know if that`s the best. Welding MiG without gas isn`t worth...
Forum: Using Tools and Welding 12-01-2007, 03:46 PM
Replies: 3
Views: 2,134
Posted By Gunnar
Question What welding equipment is best?

Hey! I got access to both MiG and gas welding equipment. What is the best to use? The MiG is easy to use and gives a smooth and solid weld, but the gas welder gives a much better melting and control...
Forum: Mini Bikes, Trikes, and Choppers 11-13-2007, 02:36 PM
Replies: 18
Views: 4,747
Posted By Gunnar
Sweet looking bike

Sweet looking bike
Forum: Mini Bikes, Trikes, and Choppers 10-13-2007, 07:51 AM
Replies: 3
Views: 1,848
Posted By Gunnar
I`ll see if I can find a piece of trash moped I...

I`ll see if I can find a piece of trash moped I can rip the engine out of at http://www.finn.no then. That would be kinda cool.
Forum: Mini Bikes, Trikes, and Choppers 10-11-2007, 09:43 AM
Replies: 3
Views: 1,848
Posted By Gunnar
What engine is best for a bike?

Hey! I was first planning to build a kart, but then I got a suggestion that I could build a mini bike for a bigger challenge. The frame I shouldn`t be a problem but what about the engine? I have a...
Forum: Introduce Yourself! 10-10-2007, 03:51 PM
Replies: 4
Views: 1,912
Posted By Gunnar
That wasn`t a very bad idea. I have been...

That wasn`t a very bad idea. I have been searching for old mopeds I can rip the engine out off on http://www.finn.no for a go kart, but maybe I should make a bike instead.... That would be kinda cool
Forum: Introduce Yourself! 10-08-2007, 02:48 PM
Replies: 4
Views: 1,912
Posted By Gunnar
Thank you very much

Thank you very much
Forum: Introduce Yourself! 10-06-2007, 03:22 PM
Replies: 4
Views: 1,912
Posted By Gunnar
Thumbs up Basics about me...

Hey, I`m 15 years old and I come from Norway. My hobbies are shooting and guitar. I`m also very interested in welding and metal work and have been doing it for a couple of years now. I share a...
Forum: Go Kart Discussion 10-06-2007, 02:52 PM
Replies: 0
Views: 964
Posted By Gunnar
I got a 3,5hp B&S engine, where to start?

Hey, I got a 3,5hp B&S lawnmover engine, loads of metal tubes, plates, square pipes etc, good welding gear and pretty good welding skill (at least for a 15 year old guy I think. have been welding for...
Forum: Go Kart Discussion 10-06-2007, 02:21 PM
Replies: 1
Views: 975
Posted By Gunnar
It looks like the frame is made of angle iron, a...

It looks like the frame is made of angle iron, a square pipe for rear axle, a round one for steering and some steel plates. Doesn`t look so complicated to me.
Forum: Go Kart Discussion 10-06-2007, 01:05 PM
Replies: 22
Views: 1,886
Posted By Gunnar
I`m 15, and I do all welding and that stuff myself

I`m 15, and I do all welding and that stuff myself
Showing results 1 to 12 of 12

 

All times are GMT -6. The time now is 06:37 AM.