Go Back   DIY Go Kart Forum > Search Forums

Notices

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: karl
Forum: Engines & Clutches 05-28-2020, 06:40 PM
Replies: 66
Views: 2,017
Posted By karl
No problem! You may want to try only adding...

No problem!

You may want to try only adding some weight first , before taking out any springs. Once dialed in, Its a nice unit. Good luck!
Forum: Engines & Clutches 05-27-2020, 06:43 PM
Replies: 66
Views: 2,017
Posted By karl
Nice, you may see some benefit after the sprocket...

Nice, you may see some benefit after the sprocket change.

Plus, mine was .30 in thick, shaving it down some , maybe .25 , might help as well.

I played with the juggernaut recently, and I can...
Forum: Off Topic Forum 05-27-2020, 06:19 PM
Replies: 46
Views: 3,281
Posted By karl
I dont think you will run into that issue, at...

I dont think you will run into that issue, at least with a gx200.

I put about half a dozen hours on the kohler command 624cc v-twin with the same turbo, stock wastegate, draw through, I think...
Forum: Engines & Clutches 05-26-2020, 07:23 PM
Replies: 18
Views: 241
Posted By karl
I dont have an explanation, but thanks for...

I dont have an explanation, but thanks for sharing! Looks like alot of fun.

I wonder if a wet shot of liquid fuel could be set up with the pressure of a pulse pump or a mini low current electric...
Forum: Photo Gallery & Project Log 05-24-2020, 12:28 PM
Replies: 109
Views: 7,816
Posted By karl
The turbo engine is fun, but a little...

The turbo engine is fun, but a little uncontrollable around the yard, and I dont want to take it on long trips.

So I happened to grab a ch670 command 22hp, that was sittin outdoors ya know. In...
Forum: Engines & Clutches 05-16-2020, 01:53 PM
Replies: 66
Views: 2,017
Posted By karl
Thanks, no clearance issues, direct fit. ...

Thanks, no clearance issues, direct fit.

Man do they hook up well! My backyard is half standing water and muck (listen to my footsteps lol), and it did great. Before in the same spots, if I hit...
Forum: Engines & Clutches 05-16-2020, 08:37 AM
Replies: 1
Views: 81
Posted By karl
Could ya give us a lil more to work with? ...

Could ya give us a lil more to work with?

Like what else did you do to the motor?

What vehicle, clutch, gear ratio, ambitions/ expectations?

Best overall performance usally sacrifices...
Forum: Engines & Clutches 05-15-2020, 08:26 PM
Replies: 66
Views: 2,017
Posted By karl
Fake news 10/10 would recommend

Fake news

10/10 would recommend
Forum: Engines & Clutches 05-15-2020, 05:12 PM
Replies: 66
Views: 2,017
Posted By karl
Sorry I will not get to it today, stupid ohio...

Sorry I will not get to it today, stupid ohio weather rained for 3 days and the garage finally flooded again after a heavy downpour, so yeah thats most my night

But they look good! Should be way...
Forum: Off Topic Forum 05-14-2020, 07:09 AM
Replies: 820
Views: 35,989
Posted By karl
Just a lil rhb31 , on the yard kart ...

Just a lil rhb31 , on the yard kart



I have not tried it, not very useful in my yard. But im happy with it, not having to empty the bagger several times.
Forum: Off Topic Forum 05-13-2020, 07:10 PM
Replies: 820
Views: 35,989
Posted By karl
I have not played terraria myself, but I played...

I have not played terraria myself, but I played minecraft in the OG days, on a Pentium 4, rough times, and years after. It is heavily updated as time goes on. And there is alot you can do, like...
Forum: Engines & Clutches 05-13-2020, 06:33 PM
Replies: 66
Views: 2,017
Posted By karl
Hope this helps. I seem to forget not everyone...

Hope this helps. I seem to forget not everyone has an abundance of scrap steel lying around. The first piece I picked up , a cutoff from an exhaust I made couple years ago worked perfect. No idea...
Forum: Engines & Clutches 05-12-2020, 08:11 PM
Replies: 66
Views: 2,017
Posted By karl
No problem, it will not affect bottom end, but if...

No problem, it will not affect bottom end, but if your motor is dogging out in the top end/ top speed, this will make a big impact.

I think this will help those more who are trying to push more...
Forum: Engines & Clutches 05-12-2020, 04:47 PM
Replies: 66
Views: 2,017
Posted By karl
So the spacer had a bigger OD, or lets say wall...

So the spacer had a bigger OD, or lets say wall thickness, than the brass spacer.

So with the factory brass spacer, the outside sheave can slide over it,
and the clutch works like normal, the...
Forum: Engines & Clutches 05-11-2020, 07:37 PM
Replies: 66
Views: 2,017
Posted By karl
Thanks, I ended up buying a pair of these, well,...

Thanks, I ended up buying a pair of these, well, cause I thunk they looked cool , should hook good. Wont take much to be better than stock.

Has anybody big block swapped a monster moto before?
Forum: Engines & Clutches 05-11-2020, 11:51 AM
Replies: 66
Views: 2,017
Posted By karl
The factory tire size is 19-7, 8in rim. I think I...

The factory tire size is 19-7, 8in rim. I think I might grab one of these.
...
Forum: Engines & Clutches 05-10-2020, 07:44 PM
Replies: 66
Views: 2,017
Posted By karl
I did try to cram the 357cc engine with a 30...

I did try to cram the 357cc engine with a 30 series into the MB 212, but it was going to take too much modification. Also a Tecumseh hm80, but again, custom mount or jackshaft. So the mud mower...
Forum: Engines & Clutches 05-10-2020, 05:28 PM
Replies: 66
Views: 2,017
Posted By karl
True, with a factory cam/power curve, it will...

True, with a factory cam/power curve, it will slightly reduce top speed.

But if your rpm is being limited , as other forum members have reported hitting a "wall" their motors cannot rev past,...
Forum: Engines & Clutches 05-10-2020, 03:08 PM
Replies: 66
Views: 2,017
Posted By karl
I found the best solution for my application, ...

I found the best solution for my application,

Its really simple, and gives the regular 30 series driver the "high rpm" capabilities of the juggernaut , with the benefit of a clutch that actually...
Forum: Engines & Clutches 05-06-2020, 11:31 AM
Replies: 66
Views: 2,017
Posted By karl
Yeah, I was just speaking for comet's ratings ...

Yeah, I was just speaking for comet's ratings

But gopowersports claims no adjustments needed! What gives? haha

Just buy it and ask questions later, right?
Forum: Engines & Clutches 05-06-2020, 07:40 AM
Replies: 66
Views: 2,017
Posted By karl
The 30 series is only rated for 8hp. The...

The 30 series is only rated for 8hp.

The red 212cc definitely exceeds that, and my mud mower is running a 30 series , behind a 357cc clone with a milled head, timing advanced , genuine large...
Forum: Engines & Clutches 05-05-2020, 07:50 AM
Replies: 66
Views: 2,017
Posted By karl
I think your right, not an identical clone, but...

I think your right, not an identical clone, but remarkably simular.

And not new at all.

Guess whats also rated at 8500rpm and is in current production, recommended for junior dragsters. ...
Forum: Engines & Clutches 05-04-2020, 07:32 AM
Replies: 66
Views: 2,017
Posted By karl
Yeah I got 22lb springs in it, with an NR 252...

Yeah I got 22lb springs in it, with an NR 252 rattlesnake cam, almost 13 to 1 compression.

No matter what I did, it still did not preform great, motor revving up way to high, and you go nowhere. ...
Forum: Engines & Clutches 05-03-2020, 08:29 AM
Replies: 66
Views: 2,017
Posted By karl
Sorry, I meant to set it as unlisted, should work...

Sorry, I meant to set it as unlisted, should work now
I hear ya, im running a gx200 head milled .040 with no gasket, on a hemi block. Id love to race ya if we were closer lol.

If your driven...
Forum: Engines & Clutches 05-03-2020, 08:21 AM
Replies: 13
Views: 146
Posted By karl
Yup, it should be difficult to assemble, and when...

Yup, it should be difficult to assemble, and when together, should snap back to resting position , if its mushy, no good.

When twisting the driven open, the spring should get tighter.
Showing results 1 to 25 of 500

 

All times are GMT -6. The time now is 03:47 PM.